Para análisis de baja conductividad, en
conjunción con un FRA externo, el 1296 puede controlar hornos, criostatos y dispone de software
SMarT
propio y de ZView para análisis de los parámetros
medidos.
Analyzing
low conductivity, low loss materials can be difficult. Impedance techniques
using traditional frequency response analyzers (FRAs) are unable to provide
accurate, repeatable results, especially at lower frequencies.
The
1296 Dielectric Interface overcomes these limitations to give you fast,
accurate and repeatable impedance measurements over 12 decades of
frequency, yielding valuable insights into the characteristics of a wide
range of materials, including polymers, rubber, wood, adhesives, electronic
components, waxes and oils, etc.
1296
enhances the capabilities of Solartron's renowned 1260 and 1255 FRAs to
cope with ultra low current and capacitance levels experienced in testing
dielectric materials, enabling :
• Impedance measurements exceeding 100Tohms
•
Accurate tan delta measurements down to 0.0001
•
Frequency range from 10µHz up to 10MHz
• AC
signal and dc bias voltages up to 1000V (with external psu or amplifier)
revealing essential data in areas previously inaccessible.
Highly
accurate reference capacitors are built in to 1296, or you can choose to
use an external reference, offering unrivalled flexibility to meet almost
every measurement need. Support for temperature and DC controllers is
integral to the measurement software, further increasing the scope for
materials analysis.
1296 comes complete with its own Windows based
application software which takes care of experimental technique and lets
you concentrate on interpreting the results. Intuitive dialog boxes enable
you to set up and control experiments quickly and simply. Results can be
displayed, stored for subsequent analysis, or directly exported to another
application, such as Excel.
Software SMaRT:
Solartron dispone del software
SMaRT (Solartron
Materials
Research and
Test software).
This software controls Solartron FRAs and
material test interfaces as well as a wide range of temperature
controllers.
|
|
|
Amplificadores
de alto voltaje
|
|
Power Supply
Web Site
|
Bandwidth (3dB)
|
Voltage Gain
|
Max Voltage with 1260/1296
|
Remote
Control Capability
|
Current Limit
|
|
Kepco BOP1000M
|
1.8kHz
|
100V/V
|
700Vrms
(1000Vpk)
|
No
|
40mA
|
|
Kepco BOP500M
|
5.3kHz
|
50V/V
|
350Vrms
(500Vpk)
|
No
|
80mA
|
|
Kepco
BOP200-1M
|
4kHz
|
20V/V
|
140Vrms
(200Vpk)
|
Yes (IEEE) 1296
driver not available yet
|
1A max. Set limit to
20mA for use with 1296
|
|
Kepco BOP100-1M
|
18kHz
|
10V/V
|
70Vrms
(100Vpk)
|
Yes (IEEE) 1296 driver
not available yet
|
1A max. Set limit to
20mA for use with 1296
|
|
Trek 20 / 20B
|
75kHz (small signal)
|
2000V/V
|
14kVrms (20kVpk)
|
No
|
20mA
|
|
Trek 609D
|
35kHz
|
1000V/V
|
4kV
|
No
|
20mA
|
|
|
|
|
|
|
|
Controladores de
temperatura
|
|
Temperature
Controller
Web Site
|
Driver Available for
1296
|
Comentarios
|
|
Eurotherm
|
Yes
|
Suministrador
recomendado
|
|
LakeShore
340
|
Yes
|
do not supply
cryostats
|
|
Criostatos
|
|
Cryostat
Web Site
|
Temp. range
|
Comentarios
|
|
Janis
SVT
|
5K a 600K
|
Suministrador recomendado
|
|
|
|
|
|
|
·
Solicitar información sobre
los productos
|
|
